{"product_id":"castle-creations-060-0091-00-sensored-brushless-motor-2400kv","title":"Castle Creations 060-0091-00 4-Pole Sensored Brushless Motor 2400KV","description":"\u003ch1\u003eCastle Creations 060-0091-00 Sensored Brushless Motor 2400KV\u003c\/h1\u003e\n\u003cp\u003eThe 1721-2400Kv motor is available to those that are ready to take their extreme speed and drag setups to the next level\u003c\/p\u003e\n\u003cp\u003eIdeal for running up to 8s LiPo in 1:8 and 1:7 scale vehicles, the mechanical design boasts a stainless-steel sleeve to reinforce and strengthen the rotor for high RPM operation. Coupled with a massive 8mm stainless steel motor shaft, 8.0mm bullets and high strand, low resistance, silicone coated 8 gauge copper wire, the 1721-2400Kv will deliver massive power and maximum top end speed.\u003c\/p\u003e\n\u003cp\u003eSPECIFICATIONS:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eInput Voltage Range:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003eMin: 4s LiPo\u003c\/li\u003e\n\u003cli\u003eMax: 8s LiPo (33.6V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eKv: 2400\u003c\/li\u003e\n\u003cli\u003eMax. RPM: 90,000\u003c\/li\u003e\n\u003cli\u003eSize:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003eDiameter: 1.87” (47.6mm) at fins, 46mm at can\u003c\/li\u003e\n\u003cli\u003eLength: 101.2mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eWeight (w\/wires): 816.4g (28.8oz)\u003c\/li\u003e\n\u003cli\u003eShaft Size:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003eLength: 22mm\u003c\/li\u003e\n\u003cli\u003eDiameter: 8mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eMounting Hole Specifications: M3 and M4 @ 25.4mm (1\")\u003c\/li\u003e\n\u003cli\u003eCooling Fan: Optional, 011-0162-00, can fit two on the 1721 series\u003c\/li\u003e\n\u003cli\u003eConnectors: 8mm male bullets on 8 gauge wire\u003c\/li\u003e\n\u003cli\u003eItems Needed for Operation: Compatible Electronic Speed Control (ESC)\u003c\/li\u003e\n\u003cli\u003eProduct Use Statements:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003eThis is an extremely powerful motor designed for advanced and experienced users only. Below are suggestions for increasing your likelihood of success but it is not guaranteed.\u003c\/li\u003e\n\u003cli\u003eThis is a VERY high RPM motor. Start with very conservative gearing (small pinion\/large spur).\u003c\/li\u003e\n\u003cli\u003eCheck your data logs, temperatures and setup closely after each run to ensure you are not stressing components.\u003c\/li\u003e\n\u003cli\u003eThis motor is intended for single passes only; allow time between runs for the ESC, batteries and motor to cool down to ambient temperatures.\u003c\/li\u003e\n\u003cli\u003eThis motor can pull very high amperages. Make sure your batteries, connectors and soldering are capable of handling the loads. Inadequate power can cause poor performance and damage the batteries and\/or ESC.\u003c\/li\u003e\n\u003cli\u003eDo NOT free rev the motor with no load, particularly when running 6s or higher. The RPM output of the motor is much higher with no load as the kv and battery voltages do not drop.\u003c\/li\u003e\n\u003cli\u003eSet ESC timing to Lowest (0). This motor will pull considerably more amperage as you increase timing. This does not necessarily equate to more speed as it puts more strain on the batteries and causes the voltage to sag. Less is more sometimes.\u003c\/li\u003e\n\u003cli\u003eDo not exceed 33.6v when using this motor.\u003c\/li\u003e\n\u003cli\u003eBe sure your pinion and motor bullets are secure before and after each run.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eRecommended ESC(s): Mamba XLX2\u003c\/li\u003e\n\u003cli\u003eRunning Modes: SmartSense™ (with Castle Sensor capable ESC), Sensored and an ultra-efficient Sensorless mode.\u003c\/li\u003e\n\u003cli\u003eTech Notes: Water Resistant Design, The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Castle Creations","offers":[{"title":"Default Title","offer_id":44043645616341,"sku":"CSE060-0091-00","price":239.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0520\/1972\/4454\/products\/castle-creations-060-0091-00-sensored-brushless-motor-2400kv.jpg?v=1677879435","url":"https:\/\/www.whiterosehobbies.com\/products\/castle-creations-060-0091-00-sensored-brushless-motor-2400kv","provider":"White Rose Hobbies","version":"1.0","type":"link"}